TP | 您所在的位置:网站首页 › openwrt wiki tp › TP |
![]() Obvious issue with these images so far seems to be the WLAN-LEDs, they just won't stop blinking after WLAN is activated. Also I cannot tell, if DFS ist working for 5-GHz. And of course the device reports itself as V4, as I didn't create an extra profile for V6. Hi again!
The WLAN-LEDs stop blinking after a while and get lit solidly. I guess, they might work correctly and the blinking is for some good reason which I just don't see... Maybe DFS-sensing or something like that My concerns regarding DFS on the 5GHz mainly foot on this thread in the forum. Reading the syslog I noticed that after configuring the 5GHz it wouldn't start due to initialization failure related do DFS, while showing ENABLED state in LuCIs wireless section. WPS didn't work then either (using wpad-openssl). Restarting the wireless device couldn't resolve this, but rebooting the whole router did. So after configuring the AP it is a good idea to reboot the router. Indeed I tend to call this a MT7613-driver issue, not a "create-support-for-C50-V6"-issue... When the 5GHz ist up, it works quite well for my "home use", meaning: I did some speedtests, but no excessive stress tests with Iperf for several hours or something like that. What can I do next to help creating Support for the V6? What has to be reviewed, tested, handed over to somebody with more knowledge and competence? This thread in developer's part of the forum is closed, so I cannot provide these information there to possibly draw somebodys attention. Best regards! Edit: Today I needed several reboots to get 5GHz up and running. Syslog looked like this: Mon Aug 9 12:39:12 2021 daemon.notice hostapd: wlan1: ACS-COMPLETED freq=5660 channel=132 Mon Aug 9 12:39:12 2021 daemon.notice hostapd: wlan1: interface state ACS->HT_SCAN Mon Aug 9 12:39:13 2021 daemon.notice hostapd: wlan1: interface state HT_SCAN->DFS Mon Aug 9 12:39:13 2021 daemon.notice hostapd: wlan1: DFS-CAC-START freq=5660 chan=132 sec_chan=1, width=1, seg0=138, seg1=0, cac_time=60s Mon Aug 9 12:39:13 2021 daemon.err hostapd: DFS start_dfs_cac() failed, -1 Mon Aug 9 12:39:13 2021 daemon.err hostapd: Interface initialization failed Mon Aug 9 12:39:13 2021 daemon.notice hostapd: wlan1: interface state DFS->DISABLED Mon Aug 9 12:39:13 2021 daemon.notice hostapd: wlan1: AP-DISABLEDEdit 2: Seems like channel 149 is more likely to succeed than others. I might change to a manually chosen channel instead of AUTO... Mon Aug 9 12:43:16 2021 daemon.notice hostapd: wlan1: ACS-COMPLETED freq=5745 channel=149 Mon Aug 9 12:43:16 2021 daemon.notice hostapd: wlan1: interface state ACS->HT_SCAN Mon Aug 9 12:43:17 2021 daemon.notice hostapd: WPS: Converting push_button to virtual_push_button for WPS 2.0 compliance Mon Aug 9 12:43:17 2021 kern.info kernel: [ 303.910064] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready Mon Aug 9 12:43:17 2021 kern.info kernel: [ 303.916821] br-lan: port 2(wlan1) entered blocking state Mon Aug 9 12:43:17 2021 kern.info kernel: [ 303.922260] br-lan: port 2(wlan1) entered forwarding state Mon Aug 9 12:43:17 2021 daemon.notice netifd: Network device 'wlan1' link is up Mon Aug 9 12:43:17 2021 daemon.notice hostapd: wlan1: interface state HT_SCAN->ENABLED Mon Aug 9 12:43:17 2021 daemon.notice hostapd: wlan1: AP-ENABLED |
CopyRight 2018-2019 实验室设备网 版权所有 |